16th Japan International SAMPE Exhibition (JISSE)
Vac Saver HT is a one way valve usable to protect vacuum bagged parts against vacuum loss which are multiple connected to a vacuum source. In case of a vacuum loss in a part which is connected to the same vacuum source, the Vac Saver HT closes automatically and protects this part against vacuum loss.
Corehold P-HA is a core holding film designed to hold honeycomb core and other core materials during machining. It is a polyester film coated on one side with a silicone free synthetic rubber adhesive. The film is supplied with a yellow backing release paper on one side.
Stretch Flow P 2000 is a knitted, polyester breather with excellent stretch properties. The high-stretch characteristics of Stretch Flow P 2000 enable it to conform to many complex contour surfaces, ensuring good application of pressure by vacuum bags.
Vac Valve 429 SS HTR was designed for high temperature cures where standard valves with silicone rubber seals fail. Vac Valve 429 SS HTR is to be used for direct connection to vacuum hoses instead of complex and expensive coupling systems.
LTC3 prepregs offer a low temperature cure and high temperature use after post cure. LTC prepregs allow the use of lower cost master model materials.
Come visit us at booth #V3 (Kay Bailey Hutchison Convention Center) at the CAMX show in Dallas, TX from 10/16-10/18! Learn more about our new products and innovations!
Thermalimide RCBS is a high performance release film treated on both sides for cure temperatures up to 761°F (405°C). Thermalimide RCBS is an ideal release film used during the forming process of thermoplastic materials and other high temperature applications.
New generation sealant tape for high temperature applications. Fast Tack HT builds tack quickly when applied to Thermalimide. Having good room temperature adhesion to the high temp bagging film reduces the time required to vacuum bag high temperature parts.
Airweave® UHT 300PGL and Airweave® UHT 450PGL are premium non-woven blended, fiberglass breather for ultra high temperature applications. It is safer to use these breathers in place of woven fiberglass breathers.
GS-333LT is a low tack version of our standard GS-333 tape. GS-333LT is a sealant tape which has been designed to take longer cures and still remove cleanly.
Flashbreaker® 1R is now available in 1” x 2” (2.54 cm x 5.08 cm) Pre-Cut Tape Strips for customers who want to reduce touch labor and minimize the use of knives and scissors to avoid risk of hand injury. In addition, it eliminates the possibility of damaging the vacuum bag. There’s 2,500 cut strips per roll.
On March 2018, Airtech supported the social program “Tambali Fii - Let's Start from Here” in Senegal (Western Africa) by offering vacuum bagging materials for resin infusion.
We are now able to offer additional tapes in Pre-Cut format to customers who want to reduce touch labor and minimize the use of knives and scissors to avoid risk of hand injury. In addition, it eliminates the possibility of damaging the vacuum bag.
Blueflow 88 is designed to efficiently distribute resin with little waste due to the low profile, tight construction. Blueflow 88 can be used with polyester, vinylester and epoxy resin systems. Wide widths available in 1.5 m (60 inches) and 2 m (80 inches).
Airtech TMGC-TX Fabrics are Triaxial Carbon Fabrics developed for the manufacture of composite molds with Airtech Toolfusion® resins.
A4000 LFST is a heat shrinkable lay-flat tube which has been oriented in the transverse direction. When exposed to heat 249 to 348°F (121 to 176°C) in a recirculating oven, tunnel oven or from a heat gun, the A4000 LFST material will shrink to closely fit the mandrel.
Airtech Advanced Materials Group has been awarded “Best Growth Partner 2017” by LM at the LM Windpower Supplier Conference in Amsterdam, Netherlands.
Airtac 3 is a new, safer spray adhesive designed for temporary bonding. Airtac 3 can be used to hold dry materials on contours and vertical surfaces. This product is ideally suited to resin infusion applications for holding reinforcement plies, release films, peel plies, and infusion mesh in place until the vacuum bag is secured. Airtac 3 has a fine pebble spray pattern which reduces airborne material. This reduces overspray and user exposure. Air trigger is sold separately.
This New Year, 2018 marks the 45th anniversary of Airtech Advanced Materials Group. The company will be celebrating all year long at all worldwide locations. To celebrate the 45th anniversary, Airtech has created a custom logo that will be featured throughout 2018 and has planned company and family events through the year.
Airtech Asia is pleased to announce the relocation to a bigger facility in the same city, Tianjin, China. This expansion will allow more office, warehouse, and manufacturing space to support its growing customer base. The new address is: No. 161 of Anyuan Road, Chagugang County, Wuqing District, 301721, Tianjin, P.R. China
Combo-Tech is our expanded product line that bonds various vacuum bagging materials together to form a better overall product and reduce “touch labor”, saving companies hours of labor expense while increasing productivity.
Filmcote® 1524 is an engineered film developed as a replacement for release liquids on the surface of mold tools. Filmcote® 1524 remains on the part surface after demold providing protection from damage or contamination during subsequent process.
Beta TX670 DISCO is a prepreg sold in sheet format. This special format allows for simpler and faster layups. Beta TX670 DISCO Prepreg has a 0°,+/-60° orientation, is quasi-isotropic within each ply, and comes with an engineered cut pattern that improves drapability.